Low Cost Single & Multi Shot Inclinometer ±0.2° for Drilling Holes

Low Cost Singleshot & MultiShot Inclinometer

Low Cost Single shot & Multi Shot Inclinometer for core orientation of drilling hole

RS-SMLT-01 (0~180°±0.2°)
1. Inclination: ±0.2°;
2. Azimuth: ±1.0°;
3. Tool face: ±0.5°.

RS-SMLT-01 Low Cost Singleshot & MultiShot Inclinometer
 

Introduction

RS-SMLT-01 Low Cost Singleshot & MultiShot Inclinometer is used for measuring the inclination angle, azimuth angle, orientation of magnetic operating face and orientation of high side operating face of at the end of the drilling hole or a specific position while drilling.

It is widely applied for survey of well-hole drilling in the fields of petroleum, coal mine and irrigation establishment.

Features

1. For various operational purposes:

Satisfying various survey purposes either for suspending measurement or self-floating measurement once equipped with different external protectors

2. High precision and reliability:

As the key part of inclinometer, acceleration sensor with a shockproof accelerometer have characteristics of high linearity, little temperature drifting and good recurrence, etc.

3. Power-off protection:

Power failure caused by shakes or pressures would not result in operational disruption or data loss.

4. Dynamic performance:

Excellent data collecting and processing in either dynamic or static performance.

5. Shock and impact-resistance:

External multi-vibrate-resist buffer, both radial and axial.

6. Low temperature environment suitable:

Normal performance at -40℃

7. Deep-well measuring:

Equipped with heat insulation protector, normal working at 250℃, under 125 MPa

Specifications

Diameter: Ф32 and Ф27

Inclination: 0~180°±0.2°

Azimuth: 0~360° ±1.0° (Well inclination ≥6°)

High side operating face: 0～360°±0.5° (Well inclination ≥6°)

Magnetic operating face: 0～360°±1.0° (Well inclination ≤8°)

Delay range: 1~99min, minimum 1min

Interval range: 1~99sec, minimum1sec (only for multi-shot)

Max. sampling: 3600 points (only for multi-shot)

Continuous working time: min 20 hrs (only for multi-shot)

Shock resistance: ≤4.5 g, 10~100Hz

Impact resistance: ≤2000 g, 0.5ms

Voltage: DC6V~DC8V

Current: under DC5V, stand-by condition ≤30 mA, data-collecting ≤150 mA

Temperature: -40℃~125℃ (max. 250℃ with heat insulation protector)

 

Rechargeable battery
 

For single shot
 

Voltage output: DC 7.2V.

Electricity output: ≥500mAh

Working Temperature: -40~125℃

Charge or discharge times: ≥800 times

Charging time: 2~4H

Discharging time: ≥30min

For multi shots

Voltage output: DC6V

Electricity output: ≥2000mAh

Working temperature: -40~125℃

Charge or discharge times: ≥800 times

Charging time: 16~17H

Discharging time: ≥12h

Application Techniques
1. Three Signal Transmission Methods of MWD Inclinometer While Drilling
2. Do you Know the Working Principle of Inclinometer ?
3. What is an Inclinometer While Drilling?
4. What Is The Initial Alignment Of The Inclinometer?
5. What do I need to pay attention to when using an inclinometer?
6. Selection And Application Of Fiber Optic Gyroscope Inclinometer

More Products
 

Gyro-While-Drilling-FOG-INS-1
Gyro While Drilling FOG INS
Small Diameter Measurement While Drilling
Small Diameter Measurement While Drilling
High-temperature North Seeking MEMS Gyro For Gyro Tools(125°C)
High-temperature North Seeking MEMS Gyro(125°C)
Low Cost Measurement While Drilling
Low Cost Measurement While Drilling
FOG Continuous Gyro Tools
FOG Continuous Gyro Tools
High Performance North Seeking MEMS Gyroscope
High Performance North Seeking MEMS Gyroscope